VO610A www.vishay.com vishay semiconductors rev. 1.7, 18-feb-13 1 document number: 81775 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 optocoupler, low input current, phototransistor output description the VO610A consists of a phototransistor optically coupled to a gallium arsenide infrared-emitting diode in a 4 pin plastic dual inline package. agency approvals (all parts are certified under base model VO610A) ? bsi: en 60065:2002, en 60950:2000 ? din en 60747-5-5, available with option 1 ? fimko en 60065, en 60335-1, en 60950-1 ? ul file no. e52744 ? cul tested to csa 22.2 bulletin 5a ? cqc gb4943.1-2011, gb8898-2011 features ? temperature range - 55 c to + 110 c ? rated impulse voltage (transient overvoltage) v iotm = 6 kv peak ? isolation test voltage (partial discharge test voltage) v pd = 1.6 kv ? rated isolation voltage (rms includes dc) v iowm = 600 v rms ? rated recurring peak voltage (repetitive) v iorm = 850 v peak ? thickness through insulation ? 0.4 mm ? material categorization: for definitions of compliance please see www.vishay.com/doc?99912 applications circuits for safe protective separation against electrical shock according to safety class ii (reinforced isolation): ? for appl. class i - iv at mains voltage ? 300 v ? for appl. class i - iv at mains voltage ? 600 v according to table 1 of iec 60664-1, suitable for: - switch-mode power supplies - line receiver - computer periph eral interface - microprocessor system interface ? ? ? ? ? ? note ? additional options may be possibl e, please contact sales office a c e c 1 23 4 17918_10 ordering information vo6 1 0a - #x0 # # t part number ctr bin package option tape and reel agency certified/package ctr (%) bsi, fimko, ul, cul 40 to 80 63 to 125 100 to 200 160 to 320 dip-4 VO610A-1 VO610A-2 VO610A-3 - smd-4, option 7 - - VO610A-3x007t - smd-4, option 8 - - VO610A-3x008t VO610A-4x008t smd-4, option 9 - - VO610A-3x009t - vde, bsi, fimko, ul, cul 40 to 80 63 to 125 100 to 200 160 to 320 dip-4 - - VO610A-3x001 - dip-4, 400 mil, option 6 - - VO610A-3x016 - smd-4, option 7 - - - VO610A-4x017t smd-4, option 8 - - VO610A-3x018t - smd-4, option 9 VO610A-1x019t - VO610A-3x019t VO610A-4x019t 10.16 mm > 0.6 mm 7.62 mm dip-# option 7 option 6 9.27 mm option 8 option 9 > 8 mm
VO610A www.vishay.com vishay semiconductors rev. 1.7, 18-feb-13 2 document number: 81775 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 notes ? stresses in excess of the abso lute maximum ratings can cause permanent damage to the device. functional operation of the devic e is not implied at these or any other conditions in excess of those give n in the operational sections of this document. exposure to abs olute maximum ratings for extended periods of the time can adversely affect reliability. (1) refer to reflow profile for soldering conditions for surface mount ed parts (smd), and wave profile for soldering conditions for through hole parts (dip), please go to assembly instructions ( www.vishay.com/doc?80054 ). note ? minimum and maximum values are testing requirements. typical valu es are characteristics of the device and are the result of en gineering evaluation. typical values are for information only and are not part of the testing requirements. absolute maximum ratings (t amb = 25 c, unless otherwise specified) parameter test condition symbol value unit input reverse voltage v r 6v forward current i f 60 ma forward surge current t p ? 10 s i fsm 1.5 a led power dissipation at 25 c p diss 100 mw output collector emitter voltage v ceo 70 v emitter collector voltage v eco 7v collector current i c 50 ma collector peak current t p /t = 0.5, t p ? 10 ms i cm 100 ma output power dissipation at 25 c p diss 150 mw coupler isolation test voltage (rms) t = 1 min v iso 5000 v rms operating ambient temperature range t amb - 55 to + 110 c storage temperature range t stg - 55 to + 125 c soldering temperature (1) 2 mm from case, ? 10 s t sld 260 c electrical characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit input forward voltage i f = 50 ma v f 1.25 1.6 v reverse current v r = 6 v i r 100 a junction capacitance v r = 0, f = 1 mhz c j 50 pf output collector emitter voltage i c = 1 ma v ceo 70 v emitter collector voltage i e = 100 a v eco 7v collector emitter cut-off current v ce = 20 v, i f = 0 a i ceo 10 100 na coupler collector emitter sa turation voltage i f = 10 ma, i c = 1 ma v cesat 0.3 v cut-off frequency v ce = 5 v, i f = 10 ma, r l = 100 ? f c 110 khz coupling capacitance f = 1 mhz c k 0.6 pf
VO610A www.vishay.com vishay semiconductors rev. 1.7, 18-feb-13 3 document number: 81775 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 note ? according to din en 60747-5-5 (vde 0884), 7.4.3.8.2 (see figure 2). th is optocoupler is suitable for safe electrical isolati on only within the safety ratings. compli ance with the safety ratings shall be ensured by means of suitable protective circuits. fig. 1 - derating diagram fig. 2 - test pulse diagram for sample test according to din en 60747-5-5 (vde0884), iec 60747 current transfer ratio (t amb = 25 c, unless otherwise specified) parameter test condition part symbol min. typ. max. unit i c /i f v ce = 5 v, i f = 1 ma VO610A-1 ctr 13 30 % VO610A-2 ctr 22 45 % VO610A-3 ctr 34 70 % VO610A-4 ctr 56 90 % v ce = 5 v, i f = 10 ma VO610A-1 ctr 40 80 % VO610A-2 ctr 63 125 % VO610A-3 ctr 100 200 % VO610A-4 ctr 160 320 % safety and insulation rated parameters parameter test condition symbol min. typ. max. unit partial discharge test voltage - ? routine test 100 %, t test = 1 s v pd 1.6 kv partial discharge test voltage - ? lot test (sample test) t tr = 60 s, t test = 10 s, (see figure 2) v pd 1.3 kv insulation resistance v io = 500 v r io 10 12 ? v io = 500 v, t amb = 100 c r io 10 11 ? v io = 500 v, t amb = 150 c (construction test only) r io 10 9 ? rated impulse voltage v iotm 6kv max. working voltages recurring peak voltage v iorm 850 v peak forward current i si 130 ma power dissipation p so 265 mw safety temperature t si 150 c creepage distance 7.6 mm 0 25 50 75 125 0 50 100 150 200 300 t si - safety temperature (c) 150 94 9182-2 100 250 ir-diode i si (ma) phototransistor p so (mw) t 13930 t 1 , t 2 = 1 s to 10 s t 3 , t 4 = 1 s t test = 10 s t stres = 12 s v iotm v pd v iowm v iorm 0 t 1 t test t tr = 60 s t stres t 3 t 4 t 2
VO610A www.vishay.com vishay semiconductors rev. 1.7, 18-feb-13 4 document number: 81775 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 3 - test circuit, non-saturated operation fig. 4 - test circuit, saturated operation fig. 5 - switching times switching characteristics (t amb = 25 c, unless otherwise specified) parameter test condition symbol min. typ. max. unit delay time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t d 3s rise time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t r 3s fall time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t f 4.7 s storage time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t s 0.3 s turn-on time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t on 6s turn-off time v s = 5 v, i c = 2 ma, r l = 100 ? , (see figure 3) t off 5s turn-on time v s = 5 v, i f = 10 ma, r l = 1 k ? , (see figure 4) t on 9s turn-off time v s = 5 v, i f = 10 ma, r l = 1 k ? , (see figure 4) t off 10 s channel i channel ii 95 10804 r g = 50 t p t p = 50 s t = 0.01 + 5 v i f 0 50 100 i f i c = 2 ma; adjusted through input amplitude oscilloscope r l = 1 m c l = 20 pf channel i channel ii 95 10843 r g = 50 t p t p = 50 s t = 0.01 + 5 v i c i f 0 50 1 k i f = 10 ma oscilloscope r l c l 20 pf 1 m t p t t 0 0 10 % 90 % 100 % t r t d t on t s t f t off i f i c t p pulse duration t d delay time t r rise time t on (= t d + t r ) turn-on time t s storage time t f fall time t off (= t s + t f ) turn-off time 96 11698
VO610A www.vishay.com vishay semiconductors rev. 1.7, 18-feb-13 5 document number: 81775 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 package dimensions in millimeters package marking (example of vo617a-3x018t) note ? only options 1, 7, and 8 are reflected in the package marking. ? the vde logo is only printed on option 1 parts. ? tape and reel suffix (t) is not part of the package marking. i178027-11 0.25 typ. 6.5 0.3 4.58 0.3 2.54 typ. 3.5 0.3 4.5 0.3 0 to 15 1.3 0.1 0.4 0.1 7.62 typ. pin 1 identifier 2.8 0.5 7.62 to 9.5 0.5 0.1 10.16 typ. 7.62 typ. option 6 8 min. 7.62 typ. 4.3 0.3 0.6 min. 10.3 max. 0.6 min. option 7 20802-38 7.62 typ. 12.1 max. 9.27 min. option 8 option 9 10.3 max. 7.62 typ. 8 min. 0.6 min. 0.1 0.1 2.54 1.78 0.76 8 min. 1.52 11.05 9.95 min. r 0.25 2.54 1.78 0.76 7.7 1.52 11.05 r 0.25 2.54 1.78 0.76 1.52 r 0.25 13.0 3.6 0.3 3.5 0.3 0.1 min. 0.25 0.1 3.5 0.3 2.7 min. VO610A-3 v ww 24
VO610A www.vishay.com vishay semiconductors rev. 1.7, 18-feb-13 6 document number: 81775 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 packing information fig. 6 - tape and reel shipping medium fig. 7 - tape and reel packing for option 7 and option 9 (1000 units per reel) device per tube type units/tube tubes/box units/box dip-4, standard and option 6 100 40 4000 top cover tape embossment embossed carrier 17998 2 0.1 4 0.1 1.75 0.1 16 0.3 7.5 0.1 1.5 0.1 12 0.1 4.65 0.1 0.35 0.1 5 max. 10 pitch cumulative tolerance on tape 0.2 x x 5 max. 4.55 0.1 section x-x 10.3 0.1 1.55 + 0.1
VO610A www.vishay.com vishay semiconductors rev. 1.7, 18-feb-13 7 document number: 81775 for technical ques tions, contact: optocoupleranswe rs@vishay.com this document is subject to change without notice. the products described herein and this document are subject to specific disclaimers, set forth at www.vishay.com/doc?91000 fig. 8 - tape and reel packing for option 8 (2000 units per reel) 24 0.3 5 max. 4 0.1 1.75 0.1 11.5 0.1 2 0.1 8 0.1 12.5 0.1 1.5 0.1 0.35 0.1 1.5 0.1 x x 5 max. r0.76 3.9 0.1 section x-x 4.65 0.1
legal disclaimer notice www.vishay.com vishay revision: 02-oct-12 1 document number: 91000 disclaimer all product, product specifications and data are subject to change without notice to improve reliability, function or design or otherwise. vishay intertechnology, inc., its affiliates, agents, and employee s, and all persons acting on it s or their behalf (collectivel y, vishay), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any o ther disclosure relating to any product. vishay makes no warranty, repres entation or guarantee regarding the suitabilit y of the products for any particular purpose or the continuing production of any product. to the maximum extent permitted by applicable law, vi shay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation specia l, consequential or incidental damages, and (iii) any and all i mplied warranties, including warra nties of fitness for particular purpose, non-infringement and merchantability. statements regarding the suitability of products for certain type s of applications are based on vishays knowledge of typical requirements that are often placed on vishay products in generic applications. such statements are not binding statements about the suitability of products for a particular application. it is the customers responsib ility to validate that a particu lar product with the properties descri bed in the product specification is suitable fo r use in a particular application. parameters provided in datasheets and/or specification s may vary in different applications an d performance may vary over time. all operating parameters, including typical pa rameters, must be validated for each customer application by the customers technical experts. product specifications do not expand or otherwise modify vish ays terms and condit ions of purchase, including but not limited to the warranty expressed therein. except as expressly indicate d in writing, vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the vi shay product could result in personal injury or death. customers using or selling vishay products not expressly indicated for use in such applications do so at their own risk. pleas e contact authorized vishay personnel to ob tain written terms and conditions regarding products designed for such applications. no license, express or implied, by estoppel or otherwise, to any intellectual prope rty rights is granted by this document or by any conduct of vishay. product names and markings noted herein may be trad emarks of their respective owners. material category policy vishay intertechnology, inc. hereby certi fies that all its products that are id entified as rohs-compliant fulfill the definitions and restrictions defined under directive 2011/65/eu of the euro pean parliament and of the council of june 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment (eee) - recast, unless otherwis e specified as non-compliant. please note that some vishay documentation may still make reference to rohs directive 2002/95/ ec. we confirm that all the products identified as being compliant to directive 2002 /95/ec conform to directive 2011/65/eu. vishay intertechnology, inc. hereby certifi es that all its products that are identified as ha logen-free follow halogen-free requirements as per jedec js709a stan dards. please note that some vishay documentation may still make reference to the iec 61249-2-21 definition. we co nfirm that all the products identified as being compliant to iec 61249-2-21 conform to jedec js709a standards.
|
